How to configure my tp link range extender on mac for tl wa830re

Once delivery has been done, the product remains the property of the client until picked by our agent or the customer has dropped off the item at designated locations as directed by Saruk. Any irresponsibility on the part of the customers shall not be tolerated.

Based on 0 reviews

Shop by Category Shop. Weight: 0. SKU : Technical Specifications Weight 0. Returns: Orders that do not qualify for a Return can be taken to respective Service Centres as applicable to respective items or as communicated by Saruk for clients within Nairobi. The following conditions can qualify the customer for a return and full refund Wrong item is delivered Item Does not switch on in the case of electronics-maximum 3 days Item delivered is sent back with the rider with seal intact e.

Gateway - The gateway should be in the same subnet as your IP address. The value can't be changed. Here you can create a wireless local area network just through a few settings.


Wireless Settings is used for the configuration of some basic parameters of the AP. Wireless Security provides three different security types to secure your data and thus provide greater security for your wireless network. MAC filtering allows you to control the access of wireless stations to the AP. Wireless Advanced allows you to configure some advanced parameters for the AP.

Throughput Monitor helps to watch wireless throughput information Wireless statistics enables you to get detailed information about the current connected wireless stations. There are six submenus under the Wireless menu shown in Figure : Wireless Settings, Click any of them, and you will be able to configure the corresponding function.

This page allows you to configure the wireless mode for your device. Six operation modes are supported here, including Range Extender and Access Point.

The available setting options for each operation mode are different from those of the other. AP function is enabled meanwhile. The wireless repeater relays signal between its stations and the root AP for greater wireless range. The default region is United States. When you select your local region from the pull-down list, the dialog shown in Figure appears below.

Click OK. Note Dialog Restricted by local law regulations, version for North America does not have region selection option. Enable Wireless Radio - Select or deselect this check box to allow or deny wireless stations to access the device. To apply any settings you have altered on the page, please click the Save button, and then you will be reminded to reboot the device.

Create a name up to 32 characters and make sure all wireless points in the wireless network with the same SSID. Channel - Determines the operating frequency to be used. The options are: 11b only - Only b wireless stations can connect to the device. Wireless security can be set on the following screen shown as Figure The security options are different for different operation mode. Disable Security - Check this box radio button to disable wireless security. If disabled, the wireless stations will be able to connect this device without encryption.

TP-Link TL-WA830RE 300Mbps Wi-Fi Range Extender

Type - You can select one of following types. WEP Key - Select which of the four keys will be used and enter the matching WEP key information for your network in the selected key radio button. These values must be identical on all wireless stations in your network. If you do not set the key, the wireless security function is still disabled even if you have selected Shared Key as Authentication Type.

Version - You can select one of following versions. PSK Passphrase - Enter a passphrase here. Group Key Update Period - Specify the group key update interval in seconds. The value can be either 0 or at least Enter 0 to disable the update. Be sure to click the Save button to save your settings on this page. You will be reminded to reboot the device after clicking the Save button.

Radius Port - Enter the port used by radius service. Radius Password - Enter the password for the Radius Server. As the configuration is the same in each operation mode, here we just take the Access Point for example.

TP-Link TL-WA830RE Wireless Range Extender Review

Operation Mode - Shows the current operation mode. The default setting is disabled. Description - Give a simple description of the wireless station. Status - Select a status for this entry, either Enabled or Disabled. To set up an entry, follow these instructions: First, you must decide whether the unspecified wireless stations can access the device or not. If you desire that the unspecified wireless stations can access the device, please select the radio button Allow the stations not specified by any enabled entries in the list to access, otherwise, select the radio button Deny the stations not specified by any enabled entries in the list to access.

  1. como grabar video en pantalla mac?
  2. True Know-How.
  3. cal mac ferry to islay;
  4. How to Configure my TP- LINK Range Extender on MAC(For TL-WA830RE V1 and TL-WA730RE V2) ?.

Enter a simple description of the wireless station in the Description field. For example: Wireless station A.

How to configure my TP- LINK Range Extender on MAC ? | TP-Link United Arab Emirates

Select Enabled or Disabled for this entry on the Status pull-down list. Click the Save button to save this entry. To add additional entries, repeat steps To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the Delete. Modify the information.

Click the Save button. Click the Enable All button to make all entries enabled Click the Disabled All button to make all entries disabled. Click the Delete All button to delete all entries Click the Next button to go to the next page and click the Previous button to return to the previous page. Click the Enable button to enable this function. Select the radio button: Deny the stations not specified by any enabled entries in the list to access for Filtering Rules.

Delete all or disable all entries if there are any entries already. Click the Add New Tx Power - Specifies the transmit power of the device. You can select High, Middle or Low which you would like. High is the default setting and is recommended. The beacons are the packets sent by the device to synchronize a wireless network.

Beacon Interval value determines the time interval of the beacons.

The default value is If the packet is larger than the specified RTS Threshold size, the device will send RTS frames to a particular receiving station and negotiate the sending of a data frame. The default value is Fragmentation Threshold - This value is the maximum size determining whether packets will be fragmented. Setting the Fragmentation Threshold too low may result in poor network performance since excessive packets is the default setting and is recommended. You can specify the value between Beacon Intervals. It is strongly recommended enabled. Enable Short GI - This function is recommended for it will increase the data capacity by reducing the guard interval time.